ADEMCO 5817 PDF

Honeywell Security Intrusion and Communications, ADEMCO, AlarmNet, IntelliSense, Apex, FBII, electronic security systems, burglary alarms and fire alarms for. Installation manual for the Honeywell wireless three-zone sensor. For help installing your , call The Honeywell is a wireless three zone sensor. Unlike other Honeywell wireless window and door sensors, the does not have an internal reed switch.

Author: Moogushura Kazigis
Country: United Arab Emirates
Language: English (Spanish)
Genre: Art
Published (Last): 13 January 2010
Pages: 332
PDF File Size: 7.29 Mb
ePub File Size: 5.54 Mb
ISBN: 613-3-92879-900-1
Downloads: 83906
Price: Free* [*Free Regsitration Required]
Uploader: Zulkidal

If concealed wiring is to be used, feed the wires through the concealed wiring entry hole at. Disengage the supplied mounting plate from the unit by inserting the blade of adwmco small screwdriver into the locking tab release window see Diagram 2 and pressing it against the case locking tab see Diagram 1 while sliding the plate downward along the case back.

Wiring Connections; Specifications – Honeywell ADEMCO Installation And Setup Manual [Page 2]

Don’t show me adwmco message again. Page of 2 Go. By pressing ‘print’ button you will print only current page. Risk of fire, explosion, and burns. If concealed wiring is to be used, feed it through the slot in the case back but do not connect. A built-in cover tamper switch is activated when the cover is removed.

Customer understands that a properly installed and maintained alarm system may only reduce the risk of a burglary, robbery, fireor other events occurring without providing an alarm, but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result.

Mounting For proper orientation of the unit in relation to its adejco mounting plate and the loop wiring, read all of this section before installing the unit. No increase or alteration, written or verbal, of the obligations of this Limited Warranty is authorized. When a satisfactory location is found, remove the battery and proceed with installation. While the transmitter is being enrolled by the control, all DIP switch positions should.

  DA 3161-1 PDF

Do not recharge, disassemble, heat above. Dispose of used batteries promptly. Seller shall have no obligation addmco this Limited Warranty or otherwise if the product s adenco altered or improperly repaired or serviced by anyone other than Honeywell factory service.

The locking tab will click as the case back locks in place. The two Auxiliary Loops are closed-circuit, with a nominal response time of mSec. Install the mounting plate, with its case holding posts pointing up in this examplein the.

Honeywell ADEMCO 5817 Installation And Setup Manual: Wiring Connections; Specifications

The has its own unique identification codes permanently assigned during manufacture. For UL installations, no contact in any 517 the loops may be more than 3 feet from the transmitter. Comments to this Manuals Your Name.

The description that follows assumes that the unit will be mounted as shown in the diagrams. For UL installations with fire zones, the position 4 ON setting must not be used. Observe correct polarity and insert the battery provided into the battery holder see. Add to my manuals Add. Seller does not represent that the product s it sells may not be compromised or circumvented; that the product s will prevent any personal injury or property loss by burglary, robbery, fire or otherwise; or that the product s will in all cases provide adequate warning or protection.

Recommendations must be included for a specific. To print the manual completely, please, download it. If a contact loop is not to be used, no connection is needed across its terminals.

Disengage the supplied mounting plate from the unit by inserting the blade of a small. The Multi-Point Universal Transmitter may have three contact loops connected to it.

  BARMER GESUNDHEITSREPORT 2009 PDF

It is not necessary to program the transmitter IDs during installation.

Although two holes are adsmco in the unit that would permit mounting directly to a surface holes “A” in Diagram 2it is recommended that the mounting plate be used, as described below, for ease in removing the unit for servicing should it become necessary.

The installer should assume the responsibility of developing 55817 offering a regular maintenance. The Primary Loop has several DIP switch selectable options that determine its connection requirements, response, and transmission characteristics see DIP switch setting table on next page.

For this application, the alignment guide strip along one edge of the plate serves no function and may be broken away, if desired.

Enter text from picture: Except in the case of the position 4 ON setting, the Auxiliary loops are not affected by. Got it, continue to print. Attach the case back to the mounting plate by sliding the keyhole slots in the case back down. The open slot at the other end of the unit cannot be used as a cover pry-off. Remove the transmitter’s cover if aedmco already off as described in Mounting Step 1.

Complain wrong Brand wrong Model non readable. The unit may, however, be installed in any direction, as long as the relationship of the unit to its mounting plate is maintained. Surface wiring should enter via the thin “breakout” area provided in. The should be treated as “RF” i. Regular maintenance and inspection daemco least annually by the installer and frequent testing by. Don’t have an account?