International Intergard is a high build, high performance, two component epoxy with excellent chemical and abrasion resistance suitable for use as part of a. International Intergard is a high build high performance two component epoxy finish. Call Intergard should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and.
A two pack, high build epoxy intermediate or finish coat with good chemical and abrasion resistance.
Intended uses For use on above water areas and in dry cargo holds as a high build intermediate 4100 finish coat on structural steel, piping etc. VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.
Consult your International Paint representative for the system best suited for the surfaces to be protected.
International Intergard – Rawlins Paints
Use in accordance with the standard Worldwide Marine Specifications. All surfaces to be coated should be clean, dry and free from contamination. High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning. Intergard should always be applied over a recommended primer coating scheme. The primer surface should be dry and free from all contamination, and Intergard must be applied within the overcoating intervals specified consult the relevant product data sheet.
Areas of breakdown, damage etc. Repair corroded areas with the specified anticorrosive scheme and apply Intergard within the overcoating intervals specified for the primer consult relevant primer data sheet. Apply the Intergard within the overcoating interval specified for the primer, consult relevant primer data sheet. Ensure that the area is clean and dry prior to application of Intergard Consult your International Paint representative for specific recommendations. Material is supplied in two containers as a unit.
Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified. DO NOT thin more than allowed by local environmental legislation. Recommended Tip Range 0.
Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.
Application by roller is recommended for small areas only. Do not allow material to remain in hoses, gun or spray equipment.
Thoroughly intrrgard all equipment with International GTA Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units. Clean all equipment immediately after use with International GTA It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays.
Do not exceed pot life Limitations. In the event welding or flame cutting is performed on metal coated with this integard, dust and fumes will be emitted which infergard require the use of appropriate personal protective equipment and adequate local exhaust ventilation.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Intergare Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards.
Take precautions to avoid skin and eye contact ie.
Actual safety measures are dependant on application methods and work environment. In common with all epoxy based coatings Intergard will exhibit chalking of the film on UV exposure.
Where a cosmetic finish with good gloss and colour retention is required, overcoat with recommended top coats. Overcoating information is given for guidance only and is subject to regional variation depending upon local climate integard environmental conditions.
Consult your local International Paint representative for specific recommendations.
Apply in good weather. Unmixed material in closed containers should be maintained in protected Storage in accordance with information given in the Storage Section of this data sheet.
Intergard 410 Epoxy Coating
Technical and application data herein is for the purpose of establishing a general guideline of the coating application procedures. Test performance results were obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published test results, or any other tests, accurately represent results found in all field environments. As application, environmental and design factors can vary significantly, due care should be exercised in the selection, verification of performance and use of the coating.
Marine Coatings Marine chemicals Marine lubricants. Intergard A two pack, high build epoxy intermediate or finish coat with good chemical and abrasion resistance. Products Marine Coatings Marine chemicals Intdrgard lubricants. Petersburg, Russia, interrgard Subject to re-inspection thereafter. Store 4410 dry, shaded conditions away from sources of heat and ignition.
Privacy & Cookies Policy
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.